Simple Butter Churn

Leave a comment

I apologize for being gone for a time. A short stint studying to become a Mechanical Engineering Technician, followed by a new job forced B.Howe & Family to take a short sabbatical. Well, things are beginning to sort themselves out around here, and we hope to be back on track shortly. In the meantime, I wanted to let you know that you haven’t been forgotten. Here is a project that kind of blind-sided me last week. But it’s quick and easy, so I thought I’d pass it along to you.

As a woodworking hobbyist you sometimes run into strange requests. My wife recently came home from a trip and presented me with a crock pot saying that I was to turn it into a butter churn. What could I do? Since I already had the pot, all I needed was the beater and lid.

It should be said that I don’t know anything about churning butter. The basic idea is to beat milk around until the fatty bits clump together. This can be done by simply shaking a mason jar partly filled with milk, or using a mixer with only one beater installed. There are many types of churns and information is readily available online.

The paddle consists of nothing more than two crossed pieces of wood mounted on the end of the dowel. To fix the paddles to the dowel, I chose to use a hardwood wedge.

The lid is fashioned from a 3/4″ thick piece of pine. I cut the shape to fit the outside of the pot, then routered the edge to allow it to sit into the pot a little. A hole slightly larger than the dowel was cut in the middle.

To finish the wood, it will be wiped with several coats of mineral oil.

And that is it. A simple and quick project that allowed me to get back into the shop and get sawdust up my nose.

If you’d like more information on making butter, here is a link to start you off: How to Use a Butter Churn”. There is a lot of information out there.

Watch for more to come in the near-future, and thanks for sticking around.

A Shoe Rack for the Closet

Leave a comment

It’s spring, finally!  And, one of the jobs which has to be addressed is cleaning out the coat closet.  The parkas get cleaned and stored, the spring coats are brought out, and winter boots are traded for running shoes.  It’s when digging out the boots that my wife starts to casually mention that we need a new shoe rack for the floor of the closet.  Within a few days the comments become more of an ultimatum.  So this is how you get this weeks blog.  We’ll be building a shoe rack.

Solid oak shoe rackOak shoe rack sketch

First we’ll measure the available space in the closet.  Then it’s out to the shop to figure out what we’re going to do.  There is a bunch of scrap oak left over from Rosemary’s Cupboard so we’ll use that.  I want to avoid plywood, so the rack will have to be made of slats.  A simple lap joint should hold the slats in place.  Arbitrarily I chose 1.5″ as the width for all the pieces.  And instead of being a single unit with two shelves, I’ll make two independent and stackable shelves, just in case  we want to use them for something else.  This is a one time job, so I’m not going to draw up a plan, just a quick sketch to help me visualize the finished product.

And here we go! The edges and slats for the tops are cut to length.  In this case the edges are 43.5″ and 12″ long, and the slats are all 9.25″ long.  Then a quick pass over the table saw to rip each piece down to 1.5″. 

The Edges:

Edge pieces and slat showing overlapThe edge pieces will need to be routered for the slats to overlap.  Install a  5/8″ straight bit on the router, set 3/8″ high.  Oak likes to splinter terribly, so to avoid problems make several shallow passes until the lap edge is 3/8″ deep.  You probably already know this but set the fence for the first shallow pass, and cut all of the edge pieces.  Then shift the fence back a bit and recut each edge piece, deepening the lap.  Repeat this until the lap is deep enough on all the pieces.  Switch out the router bit for a 1/4″ roundover bit,  and rout all the corners except the lap.

The edge pieces then need a 45“ mitre at each end so we can make the frame out of them.  To secure the corners, we drill pocket holes on the mitre and secure them with 1-1/2″ screws and glue.

The Slats:

Slats roughly laid outRepeat the routering process with the straight bit as with the edge pieces, this time putting the lap on the ends of the slats.  Use a piece of scrap as a push block to avoid tear out when the router exits the wood and as a way of maintaining the right angle as you move the slat across the bit.  As before, do several shallow passes until the lap is 3/8″ deep.  Switch the bits and roundover all other edges.

The Legs:

Legs showing pocket holes and light braceThe legs are 5.5″ x 8″ pieces of oak.  To make them look a little better, we cut a half circle out of the bottom with the band saw.  We rounded over all edges which wouldn’t be in contact with the top or the ground.  Then we added a couple of pocket holes which we will use to attach the legs to the top.  As a final touch, we cut a couple small triangles which will be glued in place as a light brace.

Assembly:

Assembled rack showing ratchet strap clampStart with the top:  Screw and glue the edge pieces together to create the top frame.  To keep everything in place while setting the screws we use ratchet straps.  These are just the ordinary webbed straps sold for cars, trailers, etc. and they are fantastic for clamping odd shapes or large pieces.

Evenly space the slats within the edge frame.  I simply glued them down, but for a stronger joint you may want to secure them with a small brad or finishing nail.

Both shoe racks drying up for the nightFlip the top over.  Position, screw and glue the legs in place on the short edges.  Glue the light braces into place.  Let the entire assembly dry up overnight.

Finishing:

Sand the entire piece and wipe clean with a cloth.  Apply the stain of your choice and finish with a couple coats of Danish Oil. 

Now you’re all set to shove your beautiful solid oak shoe rack into the deep recesses of your overstuffed closet where it will never be seen again, but you can be satisfied knowing that you produce a useful and beautiful object that will make your home a better place (if only subconsciously).

As always, if you have any questions, comments, or concerns about this post please share them with us.  Thanks for visiting.

Rosemary’s Cupboard – building with oak

Leave a comment

I like getting the odd custom job to figure out, especially when it involves materials, equipment, or techniques which I haven’t used before.  Just such an order was Rosemary’s Cupboard.  During a visit a while back, Rosemary requested a cabinet to fit beside the fridge in her kitchen.  We assessed the existing cupboards and measured up the space, then figured out what purpose the new cupboard was to serve.  We were also able to take one of the existing cupboard doors home for style and color matching.

Rosemary's Cupboard Sketch Plan

After a bit of sketching, and pondering, we came up with a relatively simple plan which would allow us to try a few new things.  The PDF of our sketch plan is available for download.  It is not by any stretch of the imagination a complete plan of the project as I tend to do a lot of work in my head rather than on paper.  But, it’ll give you the basic idea of what I was after.  This design relied on european-style hinges, drawer sliders, and rail & stile router bits.  [This means we had to go buy some more tools from Lee Valley– Yaay!]

The Body

The body of the cupboard is easy.  It’s just a simple box.  3/4″ oak plywood for the sides, top, bottom, center, and the toekick/base.  1/2″ oak plywood for the back.  The spacers, and crossers were each cut from 3/4″ oak plywood, the spacers being affixed to the sides prior to assembling the rest of the body.  Holes for the adjustable shelf pegs were also drilled.  Then the rest of the pieces were glued and nailed into place.  The 3/4″ plywood crossers being placed last.

Shop Tip:  The hardwood plywoods like to splinter when being cut.  Masking all cut lines with painters tape will reduce this a little, but to ensure good clean cuts invest in a proper cabinetry/plywood saw blade.  Unfortunately, they can run from $85 to $150 but are totally worth the investment, saving you time and waste from bad cuts.

Solid oak trim pieces were cut to create the face of the cupboard body.  These pieces will dress up and hide the plywood edges and make for clean edges.  My original plan was to drill pocket holes and screw these pieces together before attaching to the rest of the body, but I could be more accurate by just gluing and nailing to the plywood directly. 

This basically finished the body.  I would like to note the small indent at the back of the toekick.  This solves a small pet peave I have with most purchased cabinets – getting around the baseboards.  Why should the cabinet have a huge gap behind it?  Anyhow, on to the shelves.

Adjustable Shelves

The holes were drilled in the sides during the body assembly,  so all that was left here was to make the shelf itself.  It is just a piece of 3/4″ oak plywood with a 3/4″ piece of solid oak trim on each side.  The trim again hides the plywood edge, but also gives it a little extra strength to resist sagging across the 43.5″ span.  One shelf is made for the bottom cupboard, two are made for the top.

The DrawersDrawers

Basically there are two drawers here. One is roughly 6″ deep, while the other has no depth at all being just a pull-out shelf. Lets look at the pull-out shelf first. 

It is nothing more than a piece of 3/4″ oak plywood.  The drawer slides are attached on either side and a faceplate is fashioned from a piece of solid oak to cover the opening.  The faceplate is attached with screws through the front.  Plugs are fit into the screwholes after finishing.

The 6″ drawer consists of 3/4″ oak plywood sides and a 1/2″ oak plywood bottom.  Dadoes were cut into the sides to receive the bottom piece.  The drawer slides are attached to either side and a faceplate fashioned of solid oak.  The faceplate this time can be attached with screws on the inside of the drawer.

The Doors

This, I was expecting to be the hard part.  Each door required two rails (top and bottom), two stiles (left and right), and a 1/4″ oak plywood panel for the center.  The rails and bottom stile were cut from 1″x4″ oak, while the top stile came from a 1″x6″ oak piece. I cut a template for the top stile, traced it onto a 1″x6″ piece and rough cut the curve on the band saw.  Then it was time to play with the router and the new rail & stile bits.  If you’ve never used them, this is a two bit set where one bit is used to create the inside profile, while the other creates the counter-profile so that the stiles will butt cleanly against the rails.  The top stile was my main concern so I started there.  The bits have bearing wheels so they will ride against a template and act as a trim bit while shaping the edge. I taped my template to the rough cut piece and routered the inside edge. While this bit was in place I slid the other stile and rails through it. I set the other bit in the router and profiled the ends of the stiles. It was very important to use a sacrificial push block here, as the oak chips like crazy near the ends.  Test fitting  the pieces was truly satisfying as they locked tightly together.

The panel was cut from 1/4″ oak plywood.  It slides into a groove created by the rail & stile bits, so very little had to be done to it.  The curve only needed to be rough cut on the bandsaw.  All the pieces were put together, the joints of the rails and stiles were glued, but the panel was left to float.  Clamps were applied and the doors were left to cure for the night.

The HingesUnfinished Cupboard

The last structural component.  The european style hinges are again, remarkably easy to install.  They have a bit of a tolerance for error, and are easy to work with.  Do some research before buying them though.  Aside from different hinges opening at different angles (I used 107° overlay frameless ), there are different hinges for how your door is going to sit on the frame (overlay, offset, inset), and for the type of frame your mounting on (face frame, frameless).  Once you have the correct hinge just follow the instructions.  For mine, I drilled a 1-3/8″ hole with a forstner bit into the rail of the door and mounted a small clip onto the body of the cupboard for each hinge.  When they were all in the right place, I just needed to hold the door up and clip the hinge pieces together.  A few small adjustments to small screws on the hinges made sure that the doors were hanging straight and properly aligned.

Finishing

Of course, just when you get it all together and working you have to take it all apart to make it pretty.  Everything was sanded starting with 100 grit and moving down to 200 grit.  As an afterthought, all the doors and drawer faces received another pass on the  router to put a Roman Ogee profile on the outside edges.  In order to match the existing cupboards, all I needed to apply was a good coat of satin polyurethane.  If you read my previous post regarding Spray Gun Fun then you know how that went.

 Completed Cupboard

Completed cupboard interior

  And here it is, the completed cupboard.  Everything works the way it is supposed to.  It was all the correct dimensions.  A quick trip to Innisfil to deliver and install it in Rosemary’s kitchen and we were finally done.  The last thing we did was to install the anti-slam devices on the door hinges.  

We are happy that with the way it worked out.  It works very well.  It fits the space, and brings a lot more storage to the kitchen.  The construction was relatively easy, and yet it is quite attractive.  If anyone has questions or comments regarding this cupboard or the techniques used in its construction, please do so below.

Cupboard installed in kitchen

Spray Gun Fun – a Howe not to!

1 Comment

For quite some time we have been wanting to get a Spray Gun attachment for our compressor. We sometimes have large projects to put a finish on, and thought this would be the easiest way to go about it. Besides, the guys you see using them in videos and adverts are having so much fun and look so cool. Well, as it came to pass we got one for Christmas last year.Pakaging for Critter Siphon Gun

What we received was the Critter Air-Powered Spray Gun from Lee Valley Tools, Ltd.  Now, at first glance it isn’t very impressive.  I mean it’s small, about the size of a cheap garden hose nozzle.  It weighs about the same too. If the box didn’t include a Mason jar you would swear it was empty.  But it only  takes a second to realize that there are no cheap plastic parts, the nozzles and fittings are brass, and the stem is stainless steel.  As always though, the proof of the pudding is in the eating …. 

We had to wait a couple of months until we had a project of such sizable dimension as to warrant the use of the spray gun.  We had been expecting to wait until warmer spring weather so that we could try it outside. However, Rosemary’s Cupboard came about and was just screaming for a coat of polyurethane. 

Out came the gun, a quick read of the instruction sheet, grab a couple of mason jars and fill one with some leftover polyurethane from another job, fill another jar with paint thinner, grab a scrap piece of wood, fire up the compressor, stick the jar of urethane onto the gun, connect the air hose,  OMG we were having so much fun, just like those guys in the adverts …

Now, it should be stated that for safety reasons the follow is advised:

  1. Wear Personal Protection Devices – goggles, mask/respirator, a hat, coveralls, proper footwear,
  2. Work in a Well Ventilated Environment – the sprayer essentially atomizes the liquid you are applying to the material, and a lot of it will remain airborne reaching dangerous levels very quickly,
  3. Be Aware of the Fire Risk – if the finish you are using is flammable, it will be even more so when it is airborne, sparks, cigarettes, open flames should be extinguished or removed if there is any chance that they will come into contact with the airborne particles. 

Of course, we didn’t have any of that ready.  We knew we should, but that would take extra time and we wanted to play with the new toy. 

So, standing there in our street clothes with only a dust mask for protection, we closed the doors to the workshop (didn’t want the sound of the compressor to bother the neighbours, and it was 4°C and raining outside), adjusted the pressure on the compressor, and pulled the trigger … nothing happened.  A lot of air, bit no mist.  We had started out with the compressor set to about 30 psi, but remembered that that was the setting for thin fluids, polyurethane is pretty thick so we would have to turn it up.  We tried a few more times, raising the pressure with each go until we finally reached 70 psi and a beautiful, fine mist blew away from the gun at quite a fast rate, straight across my router table.  Thank god we had thought to get the paint thinner out.

After cleaning off the router table, and throwing drop clothes over it, the table saw, shelves, and workbenches nearby, we tried again.  This time we had it all right.  It worked great.  Nice clean lines, easy to control the spread, and the amount of spray.  We felt that it was time to turn this on Rosemary’s Cupboard.  This is where the gun surprised us the most.  We had been testing a semi-gloss finish, but wanted to apply a satin to the cupboard.  No problem.  Fill another Mason jar with the satin polyurethane, take the semi-gloss off of the gun and put a cap on it, put the Mason jar of paint thinner on the gun and shake it around a bit to clean the stem, spray it into a waste bucket a few times to clear the nozzle, then swap that jar out for the satin finish, and we’re ready to go.  It was really that easy!

The size of the cupboard allowed us to test the sprayer at a lot of angles.  Vertical sides, tops and bottoms of shelves, even slopes when we had to lean the cupboard over to get at the top.  It performed wonderfully the whole time.  The coat apllied nice and even, without runs or streaks.  After applying a coat to everything however, you couldn’t see the other side of the shop for all the polyurethane floating in the air, and it’s a small shop.  That’s about the time we woke up and remember that we shouldn’t neglect basic shop safety. 

While we were spraying we had heard my wife get into her car and drive off.  She usually parks in front of the large shop door.  I figured we could clear the air quicker by opening up both ends of the shop and letting the wind blow it all out.  I threw open the back door,  and depressed the button to lift the large door.  The wind whipped past me picking up clouds of sawdust and depositing it on all the surfaces we had just sprayed, and blew all the floating polyurethane straight out onto the hood and windshield of my wife’s car.  I guess, today she had chosen to take my van.

When the air was clear we closed the doors, cleaned up the gun, put everything away, and headed back into the house.  A quick trip into the washroom to wash up,  and I discovered why cover-alls, hats, and the other personal protective devices are so important.  Every inch of exposed skin, every hair on my head and arms, my clothes, everything had a very thin coating of polyurethane.  I looked like I was covered in a fine frost.  Fortunately, it hadn’t properly set so getting it off was fairly easy.  Had it been on there longer I would have been looking at a sponge bath in paint thinner.  Not something I ever intend to try.

So it was an adventure.  But these are the kind we like – if bad things didn’t happen we wouldn’t have any stories to tell.We’ll have to do a little extra sanding between coats, but nothing was ruined.

Over the next few days we would be applying several more coats.  During these coats we experimented with adjusting the nozzle to deliver different amounts of fluid.  We found it very easy to control, and after a little playing we found a pressure and nozzle setting which worked very well for the polyurethane.  We were also very careful to wear the appropriate clothing and gear, and to ventilate the shop more carefully.

Critter Air-Powered Spray Gun Reviewed:  9 out of 10!  It was amazingly easy to use and clean.  It did everything it was supposed to. The Mason jars make everything so simple, and you don’t have to go out and buy a special paint bottle like most manufacturers make you do.  Its light weight really becomes important after waving it around for an hour or so.  There were only two problems we had (that were not our own fault). First, when you have the hose connected to the gun, you can’t sit it down – it’s too back heavy.  We overcame this by clamping a short bar clamp to the underside of the worktable and hanging the gun over the bar (there is a little hook on top of the gun). Secondly, filling the Mason jars from a full 1 gallon pail was a bit of a pain.  We ended up using a ladle, after spilling it all over the place on the first try.  We’ll be looking around for a better way and let you know if we find something.

So at the end of the day, the Critter Air-Powered Spray Gun is worth every penny!

Check in next week when we’ll be featuring Rosemary’s Cupboard.

Should you use a Jig?

Leave a comment

Jig for tapering table legs on a table saw.Just to confuse things, there are two terms which need to be defined; fixture and jig. We’ll go with the Wikipedia definitions where a fixture is “a workholding or support device [to] hold a workpiece during either a machining operation or some other industrial process”, and a jig is “a type of tool used to control the location and/or motion of another tool”. The main point to grasp is that a fixture holds the material being worked, while a jig guides the tool doing the work. In the common language though, jig has become a general term to refer to either or both cases.

So, back to the question at hand. Should you use a jig? There is only one answer – Yes! Let’s look at why.

FiJig for placing center hole in Whirlwind slats.rst off, a jig gives us control. This can be both a safety and an accuracy concern. Cutting an odd-shaped piece on a table saw is made much easier by mounting the workpiece in a sled-style jig. Using a dovetail jig helps to maintain consistent spacing.

Secondly, a jig allows us to repeat an action on more than one piece. When making our Whirlwinds, we use a small jig on the drill press to ensure the center hole is correctly positioned.

Finally, they save us time and money. You don’t have to calculate and mark each cut, and there is less waste due to mistakes in measuring or while cutting.

With these points in mind, if you have a difficult or awkward operation to perform, or need to perform an action more than once, there are very few arguements for not using a jig. However, there are a couple. Principally, you have to stop working on your project to build a jig, or you have to shell out more cash to buy a commercially available jig.

Stopping to build a jig has not been much of a concern for us. Most of the simple jigs we use only take a couple of minutes to throw together, and that time is recovered when actually using the jig on our projects again and again. More complicated ones require a little more planning but even if it is only used once, the benefit of better quality control and less risk of waste outweighs the time used building the jig.Jig for cutting birdhouse walls on table saw

Cost is an issue on so many projects. As hobbyist woodworkers we’d prefer to put our cash into the project itself, however, here again we have to do some weighing. A homemade jig can be made from scrap wood, so the cost is minimal, but sometimes that just won’t cut it. Commercially available jigs are often easy to use and more versatile than the homemade one will be, but they can get quite pricey. So, we look at it the same way we would a new router bit. Will it do the job? Will we ever use it again? As long as we can answer yes to both questions, it’s pretty likely we’ll be buying one.

We may post about a specific jig in the future, but for now we hope this gets you thinking about the situations where you could have used a jig to simplify a project. There are many examples of woodworker’s jig all over the web, it seems there are as many types of jigs as there are woodworkers, so don’t be afraid to pick through them until you find the one you think will work the best. About.com has a few examples of different jigs to get you started.

Floating Shelves

Leave a comment

We are finally reaching the end of our re-design of the boy’s room. The last step is to hang some shelves across one wall. After looking into a few styles, we decided it would be a good time to try Floating Shelves. The look of them fit into the style of the room, and they have been a bit of a curiosity for us.

Floating ShelvesThere are plenty of descriptions and free plans online to explain how to build and install this style of shelf, so we only spent a few minutes looking them up. Here is one link with some decent videos which was helpful: Ron Hazelton’s Housecalls.

We played with the layout of the shelves, using painter’s tape. After several tries, we finally decided on one long shelf across the top with two lower shelves pushed to the far left. A little time spent finding and marking the studs and we were able to cut and attach spruce 2×2’s to the wall where the shelves were going to go. Then it was out to the shop to start making the shelves themselves.

We ripped some 1x pine into 1.5” strips, then chopped them to the lengths we needed for our frame. Following this, we ripped some 3/8” plywood for the shelf tops and bottoms. And finally, more 1x pine ripped to 2.25” for the facing pieces.

The lower two shelves were easy to figure out – build a frame leaving 1.5” at the back of the shelf for the 2×2, cover it with 3/8” plywood, attach the facing pieces, round over the edges, and sand. Actually, it was a lot easier than we expected. Then, it was on to the top shelf.

The top shelf was to be an 11’ span, from corner to corner, and we were instantly concerned that we wouldn’t be able to maneuver the shelf into place if it was one piece. So, the simple answer would be to split it in half, hang two shelves side by side. We chose to modify the frame for these shelves to accommodate an extra brace to go between the shelves, tying them together. Then, we added overlapping mitres to the facing pieces to make the seam between the two shelves a little less noticeable.

When it was all said and done, these shelves were very easy to make, which makes us wonder why we waited so long to try them. They look good, and seem more than strong enough for general use. And so, from one Woodworking Hobbyist to another, try building a Floating Shelf, even if it’s just for your shed or garage. You will be pleased with the results.

If you do try it, or have built them in the past, please leave a comment. Let us know how it went, or any tricks you picked up along the way.

Escaping Winter’s Chill

Leave a comment

Cold Days in Southern Ontario

Southern Ontario has been under a bit of a cold snap lately.  We’re not used to waking up to minus 27­­°C days.  But as the saying goes,”If you don’t like the weather in Southern Ontario – wait a minute!”  The warm days will soon be here. 

Fortunately, we’ve been able to avoid the cold by hiding in the shop.    The smell of the sawdust, the buzz of the saws, even the wood glue on our work clothes have a way of making us forget about the deep-freeze just outside the door.  We have been using the time well.  A few ongoing projects were wrapped up, and of course, a few new ones were started.  This website was one of the latter.

We’re hoping to share some of what we do with everyone. 

We started with our most popular product, the Camp Chair.   I don’t know who to give the credit to, but this is a wonderfully designed chair.  It collapses down to a managable size for storing, or transporting.  It’s quite sturdy, and most importantly, it’s strangely comfortable.  We’ve had reason to sit in them for hours at a time, without the back/neck pain that is usually associated with collapsible wooden chairs.  Of course, this is only our impression of them.   We’ve received nothing but good comments from the people we’ve made them for.   Hopefully, we’ll get some of them to post here.

New product pages will be added as time allows, so please stop back from time to time. Or better yet, subscribe to the site and learn about our updates as they happen.  Thanks for stopping by.  We’ll talk to you soon.